Hull Completed rebuild of delamination fix on starboard side. Located in starboard cockpit locker.   Refrigerator Picture for memo. How wires have to be connected. Drilled hole for evaporator pipes into ice chest and built shelf for refrigerator. (red and blue pipes are for water ;) ) Glassed shelf from bottom side and to hull in 3 directions. reglassed connection between ice chest and hull. To be continued... Review exhaust hose connection on transom   Interior Starboard cabinets, back walls and hull insolation. Galley Removed plywood build around galley window. found completely rotted out window frame. Plywood removed. Alot of extra space for electrical panel and ice chest access found. Just aft view on cabin today.

   Interior Set 5 minor walls for  galley cabinets and starboard storage over settee. made front panels.   To make tabbing in preside position i hot-glued wood blocks on bottom and top and then tabbed walls to the hull, inliner and deck. Next step - cut openings for the cabinets doors Structural.  Starboard cockpit locker area repair. Re-glassing two walls and rebuild de-laminated area on the hull.  Interior. Found nice bamboo roulette door ;-) in ikea   Prototyping Roulette type doors for cabinets.  Door type#1 (for head  cabinet) there enough space to accommodate door horizontally. Made model from old plywood left-overs, full scale model works well.   For other places need to hide door somewhere. Rail for this case.

 Interior Galley countertop and cabinets Original countertop consist of two parts, One with sink and food storage locker lid.   Another one covers ice chest and forms first step of companionway stairs. I have made paper template for whole countertop. I added check dimensions to be able to confirm if template is not deformed when i will lay it on new material. Countertop is removed Back side...   Left side is rotted significantly. At any case i am going to replace it. Structural. Back-stay chainplate replacement.  Old chainplate was done from unknown SS bar, and manufactured very poorly. Pin hole was off center and shifted to the edge. thickness is 3/16" So, I am going up size to 1/4" SS 316 . also installing old plate as backer. Hope it will make some difference to better side. Only thing leave me doubts is fact the plate mounted on transom with 4 x 5/16 countersink bolts (mean screw with hut).  When I started to prepare to work I found the difference in ...

Sailing Lazy sail. Only about 110% Genoa, no main hoisted. 15 knots with 20 gusts, mostly Board reach to Beam reach sail up river, then weather get to steady 20 knots with up to 28 gusts, "crew" was not ready to to sail upwind, so we motored back.   No pictures on way back ;-)  

 Engine Check oil, Run engine  for 30 min on mid RPM. Made sure all warks. All looks good, little white "oil" smoke visible, smells like burned oil ;-)  Packing is not dripping, what me little bit nervous, however an hour ride next day did not heat packing box any. Cleaned contacts on engine to control connector. Oil pressure switch contact was lost. Interior.  temporary toilet. Made plywood plate to install porta-poty and installed holders to prevent it running around.  Cut extensive piece of sanitary hose.    Facet and sink Installed facet and sink, so we can use water here. Head cabinet . Built head cabinet back, panels made outstanding "countertop" for 0.5" to prevent plywood absorb water if something will be spilled on it. Glassed right wall to the hull and deck with one layer of 1708. Autopilot drive project  progress A lot of calculations and chasing ideas. So, final plan is to make design close to wheel drive, but "on steroids". Irwin 34 s...

Interior Head walls painting.   Side by side - new and old. Little history Prep-work is done, ready to go. A lot of work, nothing to show ;-) Mostly it was a practice to use roll and tip technique and I think we had only 4 of 5 result. Looking back on job - we would need to put more brush thinner. But so far it is white! My wife maria greatestly helped with prep work and painting. I did just tapping. And all imperfections are on my hands. Masking tape left for coupe days to to let paint make good film. And final view Just me ;)   Other Just boat back view, it is hard to realize how beamy she is. I like beamy girls ;-)