Day 192, Engine coming back to the boat.

-

 Engine

Preparing engine to travel. Engine secured  to dolly. 3/4 plywood "skid board" mounted at dolly foot.



7:30AM came to marina.
Assembled the crane, hoisted engine and moved car out.
Good buy my crane, crane was made from 2x4  and 4x4 posts. Worked well for me all time I worked on engine. I decided to "donate" it  to the marina community.
Engine waits to descended.

Descend in progress. 

Two cars used.  Rope tied to engine, goes to pulley on the to of the hill. (block mounted on the car hatch),. then rope goes to second car. Second car controls rope tension. 

To slide on stairs we used 4 boards. 2 at time.



Came to the boat, chain hoist set on boom to load an engine.
In a process of hoisting
Engine is on the boat!
Lowering it in the engine compartment.
A lot of effort to put it on the place, but we have done it !
Engine is at home ;-)







 

Comments

Post a Comment

Popular posts from this blog

Day 183 1/5/25 Take engine home.

-
Image
Engine Take engine from the boat and move to home garage. Easy to say, hard to do. Water level in the lake now is 40ft below normal level. And total height drop between parking lot and docks about 70-80ft.  Marina has no lift, ramp or crane to move something more than 200 lb up way. Only way is very long stairs with 140 steps.   View form the parking lot...    Staircase we climbed up. Yes, you can see the lift, but it is only 200lb capacity and no way to use. Picture was made on the middle of the process. Based on engine spec it has to weight 400 lb. It is a lot but should be more or less bearable weight for 3-4 people. Challenge was accepted, but looks like it is heavy enough to do a problem ;-) Moving from boat to dock was very easy, just hook chain hoist to boom lift it  and swing boom to the dock. put on a dolly and roll it to staircase. After an hour of planning we (My son and I) decided to use blocks and ropes to slide it up. We mounted engine on the plywo...
Read more

Day 182 1/1/25 Engine haulout, added handle to refrigerator lid.

-
Image
 Engine. Final decision made. I convinced myself to get engine out and repair engine mount stringers bonding to hull as well do check/repair engine "on side". Taking engine on my own was an interesting challenge. I am very pleased to boat designers for big engine compartment hatch! it was the game changer. Process to get engine out. Disconnect drive shaft coupler. Before disassembling I started engine put on gear and cleaned and slightly filed cylindrical surfaces on rotating coupler to have good reverence surface for alignment later.    There was no surprises but one bolt had not lock washer and bolts was not tighten well. Remove and starter, alternator  No surprises on alternator, but starter mount nuts are hard to reach due to starter body diameter does not give space to put 19mm socket on the nut (starter is to "fat") and I had to use 20mm socket sitting little "on side". Starter and alternator removed  Undo aft engine mounts.  Nuts on mounts are tight...
Read more

Day 180 12/07/24 TIME TO SHOW INTERIOR & Cabin sole rebuild completed, Big cleaning.

-
Image
Time to show  the new interior. Welcome on the board.     General. Almost all plywood in the interior replaced with couple exclusions - Port side part of main bulkhead, walls around the head, 3 panels left in galley cabinets and some solid wood trimming parts. New starboard main bulkhead mounted. Floor replaced with high quality hard PVC flooring.  All gelcoat (white) inside is slightly sanded to refresh it and clean of "ups" epoxy drops paint and 46 years weathering, polished and waxed. Galley New galley countertop, completely rebuilt all rebuilt galley cabinets. Added drawer under stove cavity. "cap board" rebuilt, shelves have roulette doors now, Big rolling out  drawer added under the cockpit sit. New combined electric panel. Icebox rebuilt to built in refrigerator. Microwave installed on the stove gimbaled shelf under the LPG cooking surface.  Plenty of 110V outlets  mounted to avoid any splitters.    Nav desk rebuilt, Installed na...
Read more